![]() Is only searching for a single frequency rather than showing the It is often used in DTMF tone detection as an alternative to the Fastįourier Transform because it is quick with low overheard because it The Goertzel algorithm is long standing so see The tuning fork pitch and something easily generated by the Tone library I figured that would be more appropriate because you need the library to test the code anyway.īlinks a light on a 16mhz Arduino when it detects an A4 (440 hz), tone The code and the library were posted in the first post via a link. Īs stated in my last post I already fixed the audio connection to follow this suggested schematic You'd be hard pressed to damage an analog input with audio out.Įven with the volume at max an iphone/ipod wont put out more than ~3volts which would max out the reading somewhere around 613.8. On a Duemilanove or UNO pin 13 has a resistor and led on the board, but I added a brighter LED because the one on the board is rather dim and hard to see. There's no way to know what's wrong without seeing it - all of it. Įither the LED never triggered or it would trigger in +/-200 range of the target frequency. You might have been overloading the input and all it was seeing was 1023, 1023, 1023. The headphone output should also have a resistor to ground. Then the analog input pin is also connected to the centre of the divider. You should connect the headphone output through a capactor (about 0.1uF) to the centre of a 1:1 voltage divider. Then I plugged the headphone out from my iphone into A0 and ground.Īs has been pointed out, this is also not a good idea. You must have a resistor (220 ohms or higher) in series with the LED otherwise you'll probably damage pin 13 and even the whole Arduino.īut which Arduino are you using? Arduino boards have an LED on Pin 13 anyway. I put an LED between digital 13 and the ground right above it. I'm confused on how to use the FFT Library you linked me to.įor single tone detection stick with Goertzel's algorithm. ![]() How would I go about getting a frequency as a number or getting it to recognize certain frequencies? The other one only outputs data in binary form. It only provides 2 examples and one requires a codec shield. Nothing happens unless you lower the magnitude and then the LED fires in +/-100hz ranges that are no where near the target range.Īlso, I'm confused on how to use the FFT Library you linked me to. So, unless I'm missing something (which is totally possible), no damage should occur.Īlso after wiring it up correctly, with a different arduino(in case I damaged it :P), the results were exactly the same. So, its not going to short out with ground and a headphone jack is only going to put out a maximum ~3volts and a couple milliamps. In a rather oversimplified way, if it accepts a +5v input then connecting it to a ground or audio out shouldn't harm it. I did, indeed, forget that you cannot simply wire up ground to analog an expect results, but I fail to see how I may have cause damage. I already have a perfectly working hardware solution and I am now looking to eliminate it all together. Otherwise i would've just taken apart the algorithm myself and made an Arduino library.Īnyway, if anyone has any good Arduino software solutions for decoding DTMF or any suggestions on how to make this or another library work, it would be greatly appreciated. Either the LED never triggered or it would trigger in +/-200 range of the target frequency.Īs a side note, I am not very mathematically inclined. I spent some time changing the magnitude and target frequencies with no avail. I changed the "magnitude" to 500 and the led triggered from around 350 to 670 which is hugely unacceptable No matter the tone or shape generated the LED did not light. Then I plugged the headphone out from my iphone into A0 and ground. I attempted to use the library example, but the results were less than perfect. ![]() The closest thing I could find was this GitHub - jacobrosenthal/Goertzel: Arduino Library implementation of the Goertzel algorithm. My goal is to use something like this to decode DTMF tones reliably. ![]() I've been looking all over the web for a simple Arduino library for the implementation of either Goertzel or FFT.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |